## Booting kernel from Legacy Image at 82008000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4800670 Bytes = 4.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.15.0-rc2-gdc6721048d55 (merlijn@gentoo-x13) (armv7a-hardfloat-linux-gnueabi-gcc (Gentoo 10.3.0-r2 p3) 10.3.0, GNU ld (Gentoo 2.35.2 p1) 2.35.2) #8 SMP PREEMPT Sun Oct 10 13:46:01 CEST 2021 [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] OF: fdt: Machine model: Nokia N900 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000008fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000008fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp) [ 0.000000] percpu: Embedded 16 pages/cpu s34060 r8192 d23284 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64452 [ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait console=ttyO2,115200 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 225156K/260096K available (10240K kernel code, 1028K rwdata, 2224K rodata, 1024K init, 245K bss, 18556K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 4.0) with 96 interrupts [ 0.000000] random: get_random_bytes called from start_kernel+0x468/0x6c0 with crng_init=0 [ 0.000000] Clocking rate (Crystal/Core/MPU): 19.2/332/500 MHz [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.004150] TI gptimer clockevent: always-on 32768 Hz at /ocp@68000000/target-module@48318000 [ 0.006530] Console: colour dummy device 80x30 [ 0.006622] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2' [ 0.006652] This ensures that you still see kernel messages. Please [ 0.006683] update your kernel commandline. [ 0.006744] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) [ 0.124908] pid_max: default: 32768 minimum: 301 [ 0.125244] LSM: Security Framework initializing [ 0.125427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.125488] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.127868] CPU: Testing write buffer coherency: ok [ 0.127990] CPU0: Spectre v2: using BPIALL workaround [ 0.128631] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.130859] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.131317] rcu: Hierarchical SRCU implementation. [ 0.132537] smp: Bringing up secondary CPUs ... [ 0.132568] smp: Brought up 1 node, 1 CPU [ 0.132598] SMP: Total of 1 processors activated (498.89 BogoMIPS). [ 0.132629] CPU: All CPU(s) started in SVC mode. [ 0.133758] devtmpfs: initialized [ 0.177764] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 0.178344] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.178405] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.180511] pinctrl core: initialized pinctrl subsystem [ 0.183471] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.190185] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.241119] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.242736] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.316284] audit: initializing netlink subsys (disabled) [ 0.318634] thermal_sys: Registered thermal governor 'fair_share' [ 0.318664] thermal_sys: Registered thermal governor 'step_wise' [ 0.318695] thermal_sys: Registered thermal governor 'user_space' [ 0.320007] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.320098] cpuidle: using governor menu [ 0.320556] Reprogramming SDRC clock to 332000000 Hz [ 0.373535] OMAP GPIO hardware version 2.5 [ 0.417755] RX-51: Enabling ARM errata 430973 workaround [ 0.419921] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.442565] Kprobes globally optimized [ 0.460601] iommu: Default domain type: Translated [ 0.460662] iommu: DMA domain TLB invalidation policy: strict mode [ 0.463043] omap-iommu 480bd400.mmu: 480bd400.mmu registered [ 0.464233] platform 480bc000.isp: Adding to iommu group 0 [ 0.464904] vgaarb: loaded [ 0.465850] SCSI subsystem initialized [ 0.468139] pps_core: LinuxPPS API ver. 1 registered [ 0.468200] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.468261] PTP clock support registered [ 0.471313] clocksource: Switched to clocksource 32k_counter [ 0.597961] VFS: Disk quotas dquot_6.6.0 [ 0.598175] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.639434] NET: Registered PF_INET protocol family [ 0.639831] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.651672] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.652191] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.652282] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.652374] TCP: Hash tables configured (established 2048 bind 2048) [ 0.652648] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.652709] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.653137] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.654754] RPC: Registered named UNIX socket transport module. [ 0.654815] RPC: Registered udp transport module. [ 0.654846] RPC: Registered tcp transport module. [ 0.654846] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.654907] PCI: CLS 0 bytes, default 64 [ 0.660308] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.663787] Initialise system trusted keyrings [ 0.671752] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.674011] NFS: Registering the id_resolver key type [ 0.674133] Key type id_resolver registered [ 0.674163] Key type id_legacy registered [ 0.674255] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.674896] Key type asymmetric registered [ 0.674926] Asymmetric key parser 'x509' registered [ 0.675079] io scheduler mq-deadline registered [ 0.675109] io scheduler kyber registered [ 0.691833] pinctrl-single 48002030.pinmux: 284 pins, size 568 [ 0.692840] pinctrl-single 48002a00.pinmux: 46 pins, size 92 [ 0.693847] pinctrl-single 480025d8.pinmux: 18 pins, size 36 [ 0.711669] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled [ 0.718627] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a 8250 [ 0.719116] serial serial0: tty port ttyS1 registered [ 0.721374] 49020000.serial: ttyS2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a 8250 [ 2.181427] printk: console [ttyS2] enabled [ 2.241577] brd: module loaded [ 2.274810] loop: module loaded [ 2.280670] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.306457] libphy: Fixed MDIO Bus: probed [ 2.324523] i2c_dev: i2c /dev entries driver [ 2.329833] ti-soc-thermal 48002524.bandgap: This OMAP thermal sensor is unreliable. You've been warned [ 2.361480] ti-soc-thermal 48002524.bandgap: Non-trimmed BGAP, Temp not accurate [ 2.384521] sdhci: Secure Digital Host Controller Interface driver [ 2.390777] sdhci: Copyright(c) Pierre Ossman [ 2.414154] omap_hsmmc 4809c000.mmc: RX DMA channel request failed [ 2.432312] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.440338] omap_hsmmc 480b4000.mmc: RX DMA channel request failed [ 2.451446] ledtrig-cpu: registered to indicate activity on CPUs [ 2.472198] Initializing XFRM netlink socket [ 2.481719] NET: Registered PF_INET6 protocol family [ 2.503112] Segment Routing with IPv6 [ 2.506896] In-situ OAM (IOAM) with IPv6 [ 2.511016] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.532989] NET: Registered PF_PACKET protocol family [ 2.538177] NET: Registered PF_KEY protocol family [ 2.551696] Key type dns_resolver registered [ 2.556091] ThumbEE CPU extension supported. [ 2.560424] Registering SWP/SWPB emulation handler [ 2.571441] random: fast init done [ 2.580383] SmartReflex Class3 initialized [ 2.602539] Loading compiled-in X.509 certificates [ 2.748138] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 2.761444] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 2.773712] omap2-onenand 1000000.onenand: initializing on CS0 (0x01000000), va (ptrval), PIO mode [ 2.801483] Muxed OneNAND 256MB 1.8V 16-bit (0x40) [ 2.806304] OneNAND version = 0x0121 [ 2.822204] Scanning device for bad blocks [ 3.047363] omap2-onenand 1000000.onenand: optimized timings for 66 MHz [ 3.061553] 6 fixed-partitions partitions found on MTD device 1000000.onenand [ 3.068756] Creating 6 MTD partitions on "1000000.onenand": [ 3.091522] 0x000000000000-0x000000020000 : "bootloader" [ 3.098358] mtdblock: MTD device 'bootloader' is NAND, please consider using UBI block devices instead. [ 3.123840] 0x000000020000-0x000000080000 : "config" [ 3.130218] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 3.153808] 0x000000080000-0x0000000c0000 : "log" [ 3.159881] mtdblock: MTD device 'log' is NAND, please consider using UBI block devices instead. [ 3.183807] 0x0000000c0000-0x0000002c0000 : "kernel" [ 3.190124] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 3.213806] 0x0000002c0000-0x0000004c0000 : "initfs" [ 3.220214] mtdblock: MTD device 'initfs' is NAND, please consider using UBI block devices instead. [ 3.243774] 0x0000004c0000-0x000010000000 : "rootfs" [ 3.255065] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 3.284088] smc91x: not found (-19). [ 3.294281] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 3.308197] twl 1-0048: PIH (irq 23) chaining IRQs 146..154 [ 3.314239] twl 1-0048: power (irq 151) chaining IRQs 154..161 [ 3.366516] V28_A: Bringing 3150000uV into 3000000-3000000uV [ 3.401824] twl4030_gpio twl4030-gpio: gpio (irq 146) chaining IRQs 162..179 [ 3.468902] omap_i2c 48070000.i2c: bus 1 rev3.3 at 2200 kHz [ 3.480133] omap_i2c 48072000.i2c: bus 2 rev3.3 at 100 kHz [ 3.489501] omap_i2c 48060000.i2c: bus 3 rev3.3 at 400 kHz [ 3.502136] ti-sysc 480cb024.target-module: sysc_flags 00000100 != 00000110 [ 3.510650] smartreflex 480cb000.smartreflex: omap_sr_probe: SmartReflex driver initialized [ 3.520629] ti-sysc 480c9024.target-module: sysc_flags 00000100 != 00000110 [ 3.529205] smartreflex 480c9000.smartreflex: omap_sr_probe: SmartReflex driver initialized [ 3.546478] omap_hsmmc 4809c000.mmc: RX DMA channel request failed [ 3.555389] omap_hsmmc 480b4000.mmc: RX DMA channel request failed [ 3.591125] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 3.660369] Waiting for root device /dev/mmcblk0p2... [ 3.848876] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.862274] mmc0: new high speed SDHC card at address aaaa [ 3.869659] mmcblk0: mmc0:aaaa SC32G 29.7 GiB [ 3.882598] mmcblk0: p1 p2 [ 3.918548] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 3.926177] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 4.033874] mmc1: switch to bus width 8 failed [ 4.038909] mmc1: switch to bus width 4 failed [ 4.047821] mmc1: new high speed MMC card at address 0001 [ 4.062622] mmcblk1: mmc1:0001 MMC32G 29.8 GiB [ 4.081024] mmcblk1: p1 p2 p3 [ 4.097076] mmcblk1boot0: mmc1:0001 MMC32G 512 KiB [ 4.112365] mmcblk1boot1: mmc1:0001 MMC32G 512 KiB [ 4.152435] EXT4-fs (mmcblk0p2): recovery complete [ 4.161865] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 4.171966] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 4.191314] devtmpfs: mounted [ 4.197753] Freeing unused kernel image (initmem) memory: 1024K [ 4.204803] Run /sbin/init as init process [ 4.292022] Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP ARM [ 4.299530] Modules linked in: [ 4.302612] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.0-rc2-gdc6721048d55 #8 [ 4.310150] Hardware name: Nokia RX-51 board [ 4.314453] PC is at omap3_l3_app_irq+0xa0/0x130 [ 4.319152] LR is at __handle_irq_event_percpu+0x54/0x22c [ 4.324615] pc : [] lr : [] psr: 20000193 [ 4.330902] sp : c0f01e10 ip : ffffe000 fp : c0f00000 [ 4.336181] r10: c0ff9da0 r9 : c0ff9dc0 r8 : 0000001a [ 4.341430] r7 : 00000000 r6 : 00080000 r5 : 00000000 r4 : f8000000 [ 4.347991] r3 : 00080000 r2 : 00010001 r1 : 00080000 r0 : 00000000 [ 4.354583] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none [ 4.361846] Control: 10c5387d Table: 81b60019 DAC: 00000051 [ 4.367614] Register r0 information: NULL pointer [ 4.372375] Register r1 information: non-paged memory [ 4.377471] Register r2 information: non-paged memory [ 4.382568] Register r3 information: non-paged memory [ 4.387664] Register r4 information: 0-page vmalloc region starting at 0xf8000000 allocated at iotable_init+0x0/0xf4 [ 4.398284] Register r5 information: NULL pointer [ 4.403015] Register r6 information: non-paged memory [ 4.408111] Register r7 information: NULL pointer [ 4.412872] Register r8 information: non-paged memory [ 4.417968] Register r9 information: non-slab/vmalloc memory [ 4.423675] Register r10 information: non-slab/vmalloc memory [ 4.429473] Register r11 information: non-slab/vmalloc memory [ 4.435272] Register r12 information: non-paged memory [ 4.440429] Process swapper/0 (pid: 0, stack limit = 0x(ptrval)) [ 4.446502] Stack: (0xc0f01e10 to 0xc0f02000) [ 4.450897] 1e00: ???????? ???????? ???????? ???????? [ 4.459106] 1e20: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.467346] 1e40: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.475585] 1e60: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.483795] 1e80: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.492034] 1ea0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.500244] 1ec0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.508483] 1ee0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.516723] 1f00: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.524932] 1f20: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.533172] 1f40: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.541412] 1f60: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.549621] 1f80: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.557861] 1fa0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.566070] 1fc0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.574310] 1fe0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.582550] [] (omap3_l3_app_irq) from [] (__handle_irq_event_percpu+0x54/0x22c) [ 4.591766] [] (__handle_irq_event_percpu) from [] (handle_irq_event+0x5c/0xc0) [ 4.600891] [] (handle_irq_event) from [] (handle_level_irq+0xd8/0x1d4) [ 4.609344] [] (handle_level_irq) from [] (handle_domain_irq+0x8c/0xe8) [ 4.617767] [] (handle_domain_irq) from [] (__irq_svc+0x5c/0x90) [ 4.625579] Exception stack(0xc0f01ed8 to 0xc0f01f20) [ 4.630676] 1ec0: ???????? ???????? [ 4.638885] 1ee0: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.647125] 1f00: ???????? ???????? ???????? ???????? ???????? ???????? ???????? ???????? [ 4.655364] [] (__irq_svc) from [] (cpuidle_enter_state+0x260/0x494) [ 4.663513] [] (cpuidle_enter_state) from [] (cpuidle_enter+0x50/0x54) [ 4.671874] [] (cpuidle_enter) from [] (do_idle+0x1f8/0x2cc) [ 4.679321] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c) [ 4.686981] [] (cpu_startup_entry) from [] (start_kernel+0x5c8/0x6c0) [ 4.695251] Code: e0000007 e3c1103c e1913000 0affffe1 (e7f001f2) [ 4.701385] ---[ end trace 5183ed895179586c ]--- [ 4.706054] Kernel panic - not syncing: Fatal exception in interrupt [ 4.712463] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---