[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.15.0-rc2-gb2257a599bbf (merlijn@gentoo-x13) (armv7a-hardfloat-linux-gnueabi-gcc (Gentoo 10.3.0-r2 p3) 10.3.0, GNU ld (Gentoo 2.35.2 p1) 2.35.2) #1 SMP PREEMPT Sat Oct 9 18:55:39 CEST 2021 [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] OF: fdt: Machine model: Nokia N900 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000008fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000008fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp) [ 0.000000] percpu: Embedded 16 pages/cpu s34060 r8192 d23284 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64452 [ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait console=ttyO2,115200 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 225160K/260096K available (10240K kernel code, 1027K rwdata, 2224K rodata, 1024K init, 241K bss, 18552K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 4.0) with 96 interrupts [ 0.000000] random: get_random_bytes called from start_kernel+0x468/0x6c0 with crng_init=0 [ 0.000000] Clocking rate (Crystal/Core/MPU): 19.2/332/500 MHz [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.004119] TI gptimer clockevent: always-on 32768 Hz at /ocp@68000000/target-module@48318000 [ 0.006500] Console: colour dummy device 80x30 [ 0.006591] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2' [ 0.006622] This ensures that you still see kernel messages. Please [ 0.006622] update your kernel commandline. [ 0.006713] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) [ 0.124877] pid_max: default: 32768 minimum: 301 [ 0.125213] LSM: Security Framework initializing [ 0.125396] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.125457] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.127838] CPU: Testing write buffer coherency: ok [ 0.127960] CPU0: Spectre v2: using BPIALL workaround [ 0.128570] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.130828] Setting up static identity map for 0x80100000 - 0x80100078 [ 0.131256] rcu: Hierarchical SRCU implementation. [ 0.132476] smp: Bringing up secondary CPUs ... [ 0.132537] smp: Brought up 1 node, 1 CPU [ 0.132568] SMP: Total of 1 processors activated (498.89 BogoMIPS). [ 0.132598] CPU: All CPU(s) started in SVC mode. [ 0.133728] devtmpfs: initialized [ 0.177703] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 0.178283] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.178344] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.180450] pinctrl core: initialized pinctrl subsystem [ 0.183380] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.189971] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.240661] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.242279] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.309600] audit: initializing netlink subsys (disabled) [ 0.311950] thermal_sys: Registered thermal governor 'fair_share' [ 0.311981] thermal_sys: Registered thermal governor 'step_wise' [ 0.312011] thermal_sys: Registered thermal governor 'user_space' [ 0.313354] audit: type=2000 audit(0.300:1): state=initialized audit_enabled=0 res=1 [ 0.313446] cpuidle: using governor menu [ 0.313873] Reprogramming SDRC clock to 332000000 Hz [ 0.366760] OMAP GPIO hardware version 2.5 [ 0.410552] RX-51: Enabling ARM errata 430973 workaround [ 0.412750] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.435150] Kprobes globally optimized [ 0.452911] iommu: Default domain type: Translated [ 0.452972] iommu: DMA domain TLB invalidation policy: strict mode [ 0.455383] omap-iommu 480bd400.mmu: 480bd400.mmu registered [ 0.457214] platform 480bc000.isp: Adding to iommu group 0 [ 0.457824] vgaarb: loaded [ 0.458831] SCSI subsystem initialized [ 0.460662] pps_core: LinuxPPS API ver. 1 registered [ 0.460693] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.460754] PTP clock support registered [ 0.463287] clocksource: Switched to clocksource 32k_counter [ 0.592315] VFS: Disk quotas dquot_6.6.0 [ 0.592529] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.634887] NET: Registered PF_INET protocol family [ 0.635314] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.636901] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.637420] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.637512] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.637603] TCP: Hash tables configured (established 2048 bind 2048) [ 0.637878] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.637939] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.638336] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.644805] RPC: Registered named UNIX socket transport module. [ 0.644836] RPC: Registered udp transport module. [ 0.644866] RPC: Registered tcp transport module. [ 0.644897] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.644927] PCI: CLS 0 bytes, default 64 [ 0.654541] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.657714] Initialise system trusted keyrings [ 0.659057] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.665618] NFS: Registering the id_resolver key type [ 0.665710] Key type id_resolver registered [ 0.665740] Key type id_legacy registered [ 0.665832] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.666473] Key type asymmetric registered [ 0.666503] Asymmetric key parser 'x509' registered [ 0.666656] io scheduler mq-deadline registered [ 0.666687] io scheduler kyber registered [ 0.683532] pinctrl-single 48002030.pinmux: 284 pins, size 568 [ 0.684600] pinctrl-single 48002a00.pinmux: 46 pins, size 92 [ 0.685607] pinctrl-single 480025d8.pinmux: 18 pins, size 36 [ 0.703521] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled [ 0.714111] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a 8250 [ 0.714569] serial serial0: tty port ttyS1 registered [ 0.716827] 49020000.serial: ttyS2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a 8250 [ 2.173400] printk: console [ttyS2] enabled [ 2.236083] brd: module loaded [ 2.274688] loop: module loaded [ 2.280517] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.308410] libphy: Fixed MDIO Bus: probed [ 2.326568] i2c_dev: i2c /dev entries driver [ 2.331909] ti-soc-thermal 48002524.bandgap: This OMAP thermal sensor is unreliable. You've been warned [ 2.353393] ti-soc-thermal 48002524.bandgap: Non-trimmed BGAP, Temp not accurate [ 2.376373] sdhci: Secure Digital Host Controller Interface driver [ 2.382629] sdhci: Copyright(c) Pierre Ossman [ 2.406005] omap_hsmmc 4809c000.mmc: RX DMA channel request failed [ 2.424163] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.432220] omap_hsmmc 480b4000.mmc: RX DMA channel request failed [ 2.443420] ledtrig-cpu: registered to indicate activity on CPUs [ 2.465179] Initializing XFRM netlink socket [ 2.483612] NET: Registered PF_INET6 protocol family [ 2.491180] Segment Routing with IPv6 [ 2.503417] In-situ OAM (IOAM) with IPv6 [ 2.507537] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.524963] NET: Registered PF_PACKET protocol family [ 2.530120] NET: Registered PF_KEY protocol family [ 2.543609] Key type dns_resolver registered [ 2.548034] ThumbEE CPU extension supported. [ 2.552368] Registering SWP/SWPB emulation handler [ 2.573333] random: fast init done [ 2.582275] SmartReflex Class3 initialized [ 2.594451] Loading compiled-in X.509 certificates [ 2.741790] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 2.753356] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 2.775604] omap2-onenand 1000000.onenand: initializing on CS0 (0x01000000), va (ptrval), PIO mode [ 2.793426] Muxed OneNAND 256MB 1.8V 16-bit (0x40) [ 2.798248] OneNAND version = 0x0121 [ 2.814178] Scanning device for bad blocks [ 3.039154] omap2-onenand 1000000.onenand: optimized timings for 66 MHz [ 3.053466] 6 fixed-partitions partitions found on MTD device 1000000.onenand [ 3.060668] Creating 6 MTD partitions on "1000000.onenand": [ 3.083404] 0x000000000000-0x000000020000 : "bootloader" [ 3.093444] mtdblock: MTD device 'bootloader' is NAND, please consider using UBI block devices instead. [ 3.115844] 0x000000020000-0x000000080000 : "config" [ 3.122192] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 3.145751] 0x000000080000-0x0000000c0000 : "log" [ 3.151794] mtdblock: MTD device 'log' is NAND, please consider using UBI block devices instead. [ 3.175720] 0x0000000c0000-0x0000002c0000 : "kernel" [ 3.182067] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 3.205718] 0x0000002c0000-0x0000004c0000 : "initfs" [ 3.212097] mtdblock: MTD device 'initfs' is NAND, please consider using UBI block devices instead. [ 3.235717] 0x0000004c0000-0x000010000000 : "rootfs" [ 3.246948] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 3.276031] smc91x: not found (-19). [ 3.286224] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 3.300170] twl 1-0048: PIH (irq 23) chaining IRQs 146..154 [ 3.306213] twl 1-0048: power (irq 151) chaining IRQs 154..161 [ 3.358520] V28_A: Bringing 3150000uV into 3000000-3000000uV [ 3.393768] twl4030_gpio twl4030-gpio: gpio (irq 146) chaining IRQs 162..179 [ 3.460968] omap_i2c 48070000.i2c: bus 1 rev3.3 at 2200 kHz [ 3.472106] omap_i2c 48072000.i2c: bus 2 rev3.3 at 100 kHz [ 3.481475] omap_i2c 48060000.i2c: bus 3 rev3.3 at 400 kHz [ 3.493896] ti-sysc 480cb024.target-module: sysc_flags 00000100 != 00000110 [ 3.502380] smartreflex 480cb000.smartreflex: omap_sr_probe: SmartReflex driver initialized [ 3.512451] ti-sysc 480c9024.target-module: sysc_flags 00000100 != 00000110 [ 3.521057] smartreflex 480c9000.smartreflex: omap_sr_probe: SmartReflex driver initialized [ 3.538299] omap_hsmmc 4809c000.mmc: RX DMA channel request failed [ 3.547241] omap_hsmmc 480b4000.mmc: RX DMA channel request failed [ 3.583007] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 3.650299] Waiting for root device /dev/mmcblk0p2... [ 3.838104] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.851501] mmc0: new high speed SDHC card at address aaaa [ 3.858978] mmcblk0: mmc0:aaaa SC32G 29.7 GiB [ 3.871917] mmcblk0: p1 p2 [ 3.917846] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 3.928192] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 3.947814] devtmpfs: mounted [ 3.954406] Freeing unused kernel image (initmem) memory: 1024K [ 3.961364] Run /sbin/init as init process [ 4.019134] mmc1: switch to bus width 8 failed [ 4.027923] mmc1: switch to bus width 4 failed [ 4.032501] mmc1: new high speed MMC card at address 0001 [ 4.041839] mmcblk1: mmc1:0001 MMC32G 29.8 GiB [ 4.055267] mmcblk1: p1 p2 p3 [ 4.062957] mmcblk1boot0: mmc1:0001 MMC32G 512 KiB [ 4.079071] mmcblk1boot1: mmc1:0001 MMC32G 512 KiB INIT: version 2.93 booting OpenRC 0.40.3 is starting up Linux 5.15.0-rc2-gb2257a599bbf (armv7l) * Mounting /proc ... [ ok ] * Mounting /run ... * /run/openrc: creating directory * /run/lock: creating directory * /run/lock: correcting owner * Caching service dependencies ... [ ok ] * Clock skew detected with `(null)' * Adjusting mtime of `/run/openrc/deptree' to Fri Oct 8 17:37:54 2021 * WARNING: clock skew detected! [....] Starting hot-plug events dispatcher: udevd[ 12.032562] udevd[479]: starting version 3.2.9 [ 12.097503] random: udevd: uninitialized urandom read (16 bytes read) [ 12.109954] random: udevd: uninitialized urandom read (16 bytes read) [ 12.116943] random: udevd: uninitialized urandom read (16 bytes read) [ 12.358245] udevd[480]: starting eudev-3.2.9 . ok [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 14.981414] omap_ssi 48058000.ssi-controller: ssi controller 0 initialized (1 ports)! [ 15.134643] omap_ssi_port 4805a000.ssi-port: ssi port 0 successfully initialized [ 15.422424] input: TWL4030 Keypad as /devices/platform/68000000.ocp/48070000.i2c/i2c-1/1-0048/48070000.i2c:twl@48:keypad/input/input0 [ 15.447021] twl4030_madc 48070000.i2c:twl@48:madc: supply vusb3v1 not found, using dummy regulator [ 15.464996] usbcore: registered new interface driver usbfs [ 15.470703] usbcore: registered new interface driver hub [ 15.586975] st-accel-i2c 3-001d: supply vdd not found, using dummy regulator [ 15.608398] usbcore: registered new device driver usb [ 15.665374] input: twl4030_pwrbutton as /devices/platform/68000000.ocp/48070000.i2c/i2c-1/1-0048/48070000.i2c:twl@48:pwrbutton/input/input1 [ 15.690734] omapdss_dss 48050000.dss: supply vdda_video not found, using dummy regulator [ 15.722290] st-accel-i2c 3-001d: supply vddio not found, using dummy regulator [ 15.788177] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 15.827178] iio iio:device1: lis3lv02dl_accel: WhoAmI mismatch (0x3b). [ 15.864685] ehci-omap: OMAP-EHCI Host Controller driver [ 15.904541] st-accel-i2c: probe of 3-001d failed with error -22 [ 15.918548] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 15.928283] omapdss_dss 48050000.dss: supply vdda_video not found, using dummy regulator [ 16.003875] ehci-omap 48064800.ehci: EHCI Host Controller [ 16.009429] ehci-omap 48064800.ehci: new USB bus registered, assigned bus number 1 [ 16.156860] Bluetooth: Core ver 2.22 [ 16.160736] NET: Registered PF_BLUETOOTH protocol family [ 16.184844] ohci-platform: OHCI generic platform driver [ 16.191009] ohci-platform 48064400.ohci: Generic Platform OHCI controller [ ok [ 16.323638] Bluetooth: HCI device and connection manager initialized [ 16.330139] Bluetooth: HCI socket layer initialized [ 16.338897] ohci-platform 48064400.ohci: new USB bus registered, assigned bus number 2 [ 16.379302] ehci-omap 48064800.ehci: irq 93, io mem 0x48064800 [ 16.416534] Bluetooth: L2CAP socket layer initialized [ 16.421752] Bluetooth: SCO socket layer initialized [ 16.433563] ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00 [ 16.487762] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 [ 16.585479] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 done. [ 16.656249] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected. [ 16.674774] usb usb1: Product: EHCI Host Controller [ 16.685577] ohci-platform 48064400.ohci: irq 92, io mem 0x48064400 [ 16.743804] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC [ 16.751861] usb usb1: Manufacturer: Linux 5.15.0-rc2-gb2257a599bbf ehci_hcd [ 16.781280] Bluetooth: HCI UART driver ver 2.3 [ 16.812957] omapdss_dss 48050000.dss: supply vdda_video not found, using dummy regulator [ 16.835266] usb usb1: SerialNumber: 48064800.ehci [ 16.841094] Bluetooth: HCI UART protocol H4 registered [ 16.868225] twl_rtc 48070000.i2c:twl@48:rtc: registered as rtc0 [ 16.934143] hub 1-0:1.0: USB hub found [ 16.943420] Bluetooth: HCI UART protocol BCSP registered [ 16.949035] Bluetooth: HCI UART protocol LL registered [ 16.957824] omap-mailbox 48094000.mailbox: omap mailbox rev 0x40 [ 16.981018] omapdss_dss 48050000.dss: supply vdda_video not found, using dummy regulator [ 16.996032] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) [ 17.024627] hub 1-0:1.0: 3 ports detected [ 17.036041] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.15 [ 17.075561] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 17.082550] Bluetooth: HCI UART protocol Broadcom registered [....] Waiting for /dev to be fully populated...[ 17.142333] omapdss_dss 48050000.dss: supply vdda_video not found, using dummy regulator [ 17.172302] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 17.260284] usb usb2: Product: Generic Platform OHCI controller [ 17.344573] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: Initialized TWL4030 USB module [ 17.359466] usb usb2: Manufacturer: Linux 5.15.0-rc2-gb2257a599bbf ohci_hcd [ 17.424560] bq2415x-charger 2-006b: automode supported, waiting for events [ 17.445861] lp5523x: probe of 2-0032 failed with error -22 [ 17.475402] usb usb2: SerialNumber: 48064400.ohci [ 17.487640] bq2415x-charger 2-006b: driver registered [ 17.493621] bq27xxx-battery 2-0055: battery is not calibrated! ignoring capacity values [ 17.515136] hub 2-0:1.0: USB hub found [ 17.560333] omapdss_dss 48050000.dss: supply vdda_video not found, using dummy regulator [ 17.569610] panel-sony-acx565akm spi0.2: acx565akm rev 8d panel detected [ 17.577453] hub 2-0:1.0: 3 ports detected [ 17.614227] input: TSC2005 touchscreen as /devices/platform/68000000.ocp/48098000.spi/spi_master/spi0/spi0.0/input/input2 [ 17.666198] nokia-bluetooth serial0-0: Frame reassembly failed (-84) [ 17.772369] DSS: OMAP DSS rev 2.0 [ 17.998474] mc: Linux media interface: v0.10 [ 18.050079] Driver for 1-wire Dallas network protocol. [ 18.249755] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.5. Driver in Interrupt mode [ 18.345520] omap-sham 480c3000.sham: hw accel on OMAP rev 0.9 [ 18.355621] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 18.384277] omap-sham 480c3000.sham: will run requests pump with realtime priority [ 18.562499] videodev: Linux video capture interface: v2.00 [ 18.588226] w1_master_driver w1_bus_master1: Attaching one wire slave 01.000000000000 crc 3d [ 18.672851] nokia-bluetooth serial0-0: Direct firmware load for nokia/bcmfw.bin failed with error -2 [ 18.682312] nokia-bluetooth serial0-0: hci0: Failed to load Nokia firmware file (-2) [ 18.690246] nokia-bluetooth serial0-0: Could not setup FW: -2 [ 19.272186] power_supply bq27000-battery: power_supply_get_battery_info currently only supports devicetree [ 19.486755] omap3isp 480bc000.isp: supply vdd-csiphy1 not found, using dummy regulator [ 19.597930] omapdss_dss 48050000.dss: bound 48050400.dispc (ops dsi_vc_flush_receive_data [omapdrm]) [ 19.624694] omap3isp 480bc000.isp: supply vdd-csiphy2 not found, using dummy regulator [ 19.669921] omapdss_dss 48050000.dss: bound 48050c00.encoder (ops dsi_vc_flush_receive_data [omapdrm]) [ 19.698944] omap3isp 480bc000.isp: Revision 2.0 found [ 19.785095] omap-iommu 480bd400.mmu: 480bd400.mmu: version 1.1 [ 19.791931] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CCP2 was not initialized! [ 19.809112] omapdrm omapdrm.0: DMM not available, disable DMM support [ 19.972869] pvrsrvkm 50000000.gpu: Enabling quirks 00000000 [ 19.997131] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CSI2a was not initialized! [ 20.097259] input: gpio_keys as /devices/platform/gpio_keys/input/input3 [ 20.118682] [drm] Initialized pvr 1.17.4948957 20110701 for 50000000.gpu on minor 1 [ 20.144104] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CCDC was not initialized! [ 20.219207] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP preview was not initialized! [ 20.243591] rx51-audio n900-audio: snd_soc_register_card failed (-517) [ 20.311187] rc rc0: Unspecified device as /devices/platform/n900-ir/rc/rc0 [ 20.327209] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP resizer was not initialized! [ 20.352661] random: crng init done [ 20.364166] isp1704_charger isp1707: registered with product id isp1707 [ 20.393585] random: 2 urandom warning(s) missed due to ratelimiting [ 20.412292] rc rc0: lirc_dev: driver ir_rx51 registered at minor = 0, no receiver, raw IR transmitter [ 20.435791] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP AEWB was not initialized!